6/8/2023 0 Comments Turn on disk led hp![]() Logicaldrive 3 (465.7 GB, 0): Transforming, 0. ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 modify rebuildpriority=high Physicaldrive 2I:1:6 (port 2I:box 1:bay 6, 500 GB): OK ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld all show status ~ Migrate RAID0 to RAID1 online with hpacucli ~ # /opt/hp/hpssacli/bin/hpssacli rescan ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 create type=ld drives=2I:1:5 raid=0Ĭonfirm new disk creation by checking status of all Logical Disks ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld all show status Notice new HDD 2I:1:5 Create new Raid 0 Logical Disk using HDD 2I:1:5 ~ # Physicaldrive 2I:1:5 (port 2I:box 1:bay 5, 500 GB): OK Physicaldrive 1I:1:4 (port 1I:box 1:bay 4, 146 GB): OK On the server I am looking at, I do not see that option under System in the Tasks tab. Physicaldrive 1I:1:3 (port 1I:box 1:bay 3, 146 GB): OK Physicaldrive 1I:1:2 (port 1I:box 1:bay 2, 72 GB): OK The activity LED flashes whenever the drive is accessed. Each drive carrier in your enclosure has two LEDs: an activity LED (green) and a status LED (bicolor, green/amber) as shown below. Physicaldrive 1I:1:1 (port 1I:box 1:bay 1, 72 GB): OK The LEDs on the physical disk carrier indicates the state of each physical disk. ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 pd all show status Click the Download button and install the latest HP PC Hardware Diagnostics. ![]() ![]() Use the "show" command for more information. ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld 3 modify raid=1Įrror: The logical drive is in a state which prevents this operation fromĬompleting. ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld 3 add drives=allunassigned ~ # Scan for new HardDisk ~ # /opt/hp/hpssacli/bin/hpssacli rescan Check status for all Logical Disks ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld all show statusĬheck Status of all Physical Disks ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 modify rebuildpriority=high To ensure data loss, please backup the content immediately and run the Hard Disk Test is System Diagnostics. Enjoy Check ESXi Version ~ # esxcli -version The SMART hard disk check has detected an imminent failure. As usual, since it took me to search around Google, I simply decided to document it for future references, after all it’s just easier to read your own instructions than someone elses. It was picking it up via vCenter and I found that because I am using HP server hpssacli command was the only (best way?) way to add this new disk as RAID 0 (I had just 1 disk as my other one failed). Unless it is under warranty, then you should contact the manufacturer.I ran into some snag when I tried to add a new HDD to my ESXi server. NOTE: While the battery may be complicated to get to, it should be replaceable. Should that not be the problem, then check the battery to see if it needs replacing. If it works then, the cord is probably the issue. You may also want to try charging it when the device is off, rather than on. Either try your cord in another device, or try another devices cord in your laptop. If this doesn't help, then test the power cord to see if it is good. Press and hold the "Power" button for 30 seconds.Ĥ. The command as the CLI is as follows: esxcli storage core device set -d naaid -llocator -L60 This command basically says light the LED on the disk with the above NAA id for 60 seconds. Try the following and see if it will turn on.ģ. First, this blinking of disk LEDs can be done from both the UI and the command line. If you can't see on the external monitor at all, or the problem occurs on the external monitor as well, then it is probably the graphics card/GPU that is the problem, which may require the motherboard be replaced. If you can see fine on the external monitor, then your attached display, or the ribbon cable that connects it, are your problem. To turn off the disk UID, identify the controller and physical drive location. rootlinux: hpacucli ctrl slot3 pd 2:2 modify ledon. Could be the f4 button or a button with two monitors on it, for the external monitor to work. physicaldrive 2:2 (port 2:id 2, Parallel SCSI, 146.8 GB, OK) To turn on the disk UID, identify the controller and physical drive location. NOTE: You may have to press an "external monitor" button. ![]() Connect an external monitor to the laptop. Turn the laptop off (not sleep or hibernate but off).Ģ. So this laptops hard drive led flashes in a pattern, 1 long then 6 short, its an hp mini and i don't know if its a diagnostic code or if its something weird but the laptop won't. When I turn it on the power led comes on and everything powers on but HHD led does not. However, if the laptop doesn't turn on at all, no sounds coming from inside, try option 2.ġ. 1 My computer have been having problems shutting down and restarting and now it will no longer post. Check the power supply LED at the back of the tower before unplugging the AC power from the system the next time this happens. If the laptop has some internal sounds and lights, but nothing on the screen, try option 1.
0 Comments
Leave a Reply. |